Falcon Windows Ltd
Company No: 4128665
Falcon Windows Ltd
Brook house Business Park
Hadleigh Road Industrial Estate
Home is important. So is saving energy and keeping your bills down. And it all starts with choosing the most energy efficient home improvement products. Almost half of all the UK's carbon dioxide emissions come from our buildings and homes. Windows play a huge role in this. According to the Energy Saving Trust, more than 20% of the heat lost from an average home occurs through the windows. The heat lost contributes half a tonne of CO2 per home to the atmosphere and increases fuel bills.
Of course all standard double glazing offers a degree of energy efficiency by trapping air between two panes of glass and creating an insulating barrier. But recent technological advancements mean next generation double glazing can now cut your fuel bills, reduce noise and eliminate condensation.
Installing double glazing can cut your heating bills by £110 a year as well as 620 kilograms of CO2 - that's 3 double Decker buses full of CO2 each year. If everyone in the UK that could, installed double glazing, it would save £660 million and 4.5 million tonnes of CO2. If all 26.5 million homes in the UK were to install Energy Saving Recommended windows, we'd save a further 12.8 million tonnes of CO2 per annum, the equivalent to removing 840,000 cars off the road
Window Energy Ratings
We all know washing machines and freezers are energy rated, but did you know windows are too? They are energy rated by the British Fenestration Ratings Council on a scale of A-G. Windows achieving a rating of C and above are endorsed by the Energy Saving Trust's Energy Saving Recommended (ESR) scheme and carry the EST's swing tag logo.
Choose energy rated windows that are fitted with Super Spacer and you'll significantly reduce heat loss from your home. So you'll only replace your windows once, save money on your heating bills - and seriously reduce your carbon footprint for many years to come.
Super Spacer Warm Technology
Standard windows use a highly conductive metal spacer bar to hold the two panes of glass apart, which sucks heat from inside to the outside. Super Spacer introduces no-metal warm edge technology to windows, helping to deliver windows of the highest and most energy efficient standards. Windows using Super Spacer achieve the highest Window Energy Ratings.
Super Spacer is 950 times less conductive than traditional aluminium spacers and, as most of the heat loss through a window occurs at the edge of the unit, standard metal spacer bars act as a thermal energy drain allowing heat to escape from your home. Super Spacer blocks the escape route.
There are many other benefits of installing windows with Super Spacer. It reduces condensation by up to 70% virtually eliminating the potential breeding ground for bacteria, mould and dust mites that can be harmful to people with respiratory diseases. Super Spacer also reduces noise transmission by up to 2dB which helps you keep your home an oasis of calm, away from the noise of the outside world.
Super Spacer is equally at home in PVC-U, timber or aluminium frames so you can have energy efficient windows whatever the style of property.
Super Spacer is a no-metal, pre-desiccated, structural foam spacer system. Its award winning, patented Thermal Set Spacer (TSS) technology gives the ultimate in high performance spacer systems. Since it was first introduced in 1989, Super Spacer has become the dominant force in thermally efficient spacer systems. Super Spacer has 100% memory and allows for expansion and contraction, a major cause of breakdown in conventional sealed units. It has been subjected to rigorous testing worldwide and is proven to withstand temperatures from -15 degrees to 125 degrees, well beyond any temperatures we experience in the UK.
Are you looking for a reputable double glazing company?
Have you ever been in the situation before where you have struggled to find a good reputable window company or has anyone ever asked if 'you know a good double glazing company?'
If you are looking for a good reputable DG company then word of mouth is always a good start. Another way is by looking on the Internet to search for a recommended and reputable local double glazing and conservatory companies
Simply go online and type in 'I am looking for a double glazing company in Chelmsford' or Newmarket, Southampton , Newcastle for example. Naming the town where you live will help narrow down the search so that you can find a good reputable local company
Internet Search engines such as Google will then highlight a few options for you to consider. I would highly recommend that you arrange a free no obligational quotation. This will give you the opportunity to meet the representative of the company in person so that you can get to know how they conduct themselves. You can tell a lot about a company by the initial visit
Building a rapport with a good trustworthy company before committing to any type of contract is definitely worthwhile. Communication and ensuring that every aspect of a project is discussed is extremely important before is starts. Crossing all the T's and dotting all the dot's!
Most sound companies offer a good open and honest service and are very trust worthy when it comes to customers paying for the work that is going to be carried out.
A repair service to all types of leaking conservatories
If you are experiencing problems with a leaky conservatory roof or conservatory boxed gutter and you`re in Ipswich you can contact Falcon Windows as we are experience conservatory leak repair specialists. We can repair all types of conservatory leaking issues and we are one of the very few companies who actually take on this type of work. We basically give your conservatory an MOT!
We offer a swift affordable repair service for all types of conservatories in and around Ipswich and Suffolk. Our friendly professional tradesmen have many years worth of experience in solving leaks on conservatories and or orangeries. When we call out to site we offer advice on how one can help prevent leaks to your conservatory in future. We give you a full written quotation and if you proceed we then carry the work out within 2 weeks
We use the best available materials on the market that allow us to do the job once only to get over the problem and sometimes we have to go back to basics and strip the roof back until we find where the leak is coming in. Once finished we end up with a professional finish and also a leak free conservatory
Please contact us on (01473) 288690 or if you like direct line number (07887) 525155 and then would arrange convenient time to call out and quote for your requirements
Falcon Windows - discover the difference.
So, why choose us? At Falcon Windows, we're different! Call today and see the difference. Experience our passion for giving exceptional service and ensuring purchasing from Falcon is as easy as 123!
Once our Windows, Doors or Conservatory are installed you can sit back and enjoy the comfort and security they bring into your life allowing you to relax and feel safe in your own home
How many companies do you know, that have over 30 years' experience in both the offering and the servicing of their guarantees relating to windows, doors and conservatories?
Which company invests profits in Research and Development sure that their products are not only pleasing to the eye, but have a certification to back the technology used?
Which company installs glass/windows and conservatories in Ipswich, and the whole of Suffolk with the customers' interests in mind, installing products to the recommended codes of practice by the Glass & Glazing Federation?
Which company can you contact 24 hours a day, 7 days a week and actually speak to a representatives for an emergency call out, or any other service that we offer? Please call mobile in the Yellow Pages.
THE ANSWER TO ALL OF THE QUESTIONS ABOVE:
- All calls are logged
- Full details of the situation are taken
- Any further information needed will be taken from our existing customer files
- Service call documentation will be handed to the After Sales Technician
- After the service call has been completed a full report will be written for future referral
- Signature of customer satisfaction completes the call
This single carport is 20ft long by 10ft wide. It is the most basic of carports. Because each site is different, and individual preferences vary, we have given options for both post installation and bracing. Check with your Local Authority to see if any permit or consent is required.
The timber for this project can be either sawn (rough sawn) or dressed (gauged, smooth finish). The measurements used in this project are for sawn timber. If dressed timber is preferred, make allowances for the difference in timber thickness and width.
Use a timber suitable for in-ground applications for the posts and use a timber suitable for exterior applications for the rest of the carport structure.
Any timber merchant or supplier will be able to advise on the timber most suitable.
The height of a carport is in most cases, common sense. A tall person should be able to walk comfortably under the lowest end of the carport. 7ft from the finished ground to the underside of the lowest end rafter, is a good height.
The roof slope (fall) should be at least 2". In this project the slope is 4". If using a clear PVC roof, then a steeper slope is advisable, as a steeper fall (say 6") means faster water run-off, and therefore a cleaner roof.
The plans (click on the thumbnail) show a flat plan "bird's-eye view" and an elevation (side) plan giving all dimensions. Refer to these plans for any required measurements throughout the project.
Mark out the carport (20ft x 10ft rectangle) and erect timber profiles out from each corner and also out from the middle to take in the two center posts. Set the timber profiles back at least 2'-O" from the building line (carport perimeter) to allow room for hole digging etc. For instructions on making timber profiles attach string lines to indicate the centres of the six posts 4" in from the side edges and 13" in from the front and back edges.
INSTALLING THE POSTS
Method 1. Post set in concrete.
Dig post holes 1'-0" square by 2'-0" deep. Place 4" of concrete into the bottom of every hole.
Commence putting the posts in the holes against (but not touching) the string line. Using a spirit-level on both the front and side faces, check that the post is plumb (vertical) and almost, but not quite, touching the string line.
Fill the hole with concrete to within 2" of the finished ground level. Check again that the post is plumb and not quite touching the string line. Because of the depth of the hole, the concrete will support the post without the need for bracing. Continue until all posts are concreted in.
Method 2. Galvanized post brackets set in concrete.
post holes 1'-0" square by 2'-0" deep. Fill the holes with concrete and set the brackets in position while the concrete is still soft. Ensure the brackets are at the right height, taking the finished slab (carport floor) into consideration. Some temporary packing, props or bracing may be needed to support the brackets until the concrete stiffens up. Wait until the concrete has cured (usually at least four days) and then install the posts plumb (vertical) in the brackets and hold in place with temporary bracing.
Method 3. Galvanized post brackets bolted to existing concrete slab.
Fix the brackets to the slab, in position with masonry bolts or anchors. Install the posts plumb (vertical) in the brackets and hold in place with temporary bracing.
TRIMMING THE POSTS
Mark the rear posts a minimum of 7'-8" above the slab, or finished ground level. Ensure the height marks on both rear posts are level. Use a spirit-level on a straight edge to achieve this or the water level method. Mark the front two posts 4" higher than the rear posts. Fix a string line between the front and back posts to mark the height of the middle posts. Cut the tops of the posts off at these marks.
THE BEAMS AND RAFTERS
Cut the two beams 20ft long with 45degree angle cuts each end and clamp in place to the posts so that the tops of the beams are flush with the tops of the posts and protrude past both the front and rear posts by 1'-0". Drill and bolt the beams to the posts with 1/2" Galvanized bolts, (two at each meeting).
Cut the two end rafters 10ft long with 45degree angle cuts each end and fix in place to the beams with 3" jolthead Galvanized nails and then with Galvanized angle brackets, each bracket fixed with four 1/2" Galvanized bolts, two through the beam and two through the rafter. (See diagram).
Cut the six intermediate rafters 9'-8" long and fix in place to the beams with Galvanized metal joist hangers. Space the rafters at 3'-0" centres
Finish off with a longitudinal row of trimmers (noggings) down the middle and in between the rafters.
If the posts are concreted into the ground, and the posts are bolted to the beams with two bolts at each meeting, then no further bracing should be required. If, however, the posts are not in-ground, but supported by Galvanized post brackets, then additional bracing is required. One such scenario is to fix upper post diagonal bracing, two to each post, each about 3'-0" long (more or less), and fixed to the post with nail plates and fixed to the beam/rafter with bolts.
Another scenario is to fix full 4"x4" diagonal braces running from the bottoms of the middle posts to the tops of the end posts and secure with bolts, nail plates or Galvanized brackets at each end. A similar diagonal brace is also required between the two rear (end) posts. With this latter scenario, the diagonal braces could be replaced with diagonal trellis (lattice) between the two end posts and the end post and middle post each side (three panels in all). Both bracing methods mentioned in this scenario also require roof plane bracing to ensure the front of the carport is rigid. This can be 1" wide flat Galvanized metal strapping stretched from corner to corner and fixed with Galvanized nails to the top of each rafter.
The Terms and Conditions of using this website are as follows:
Definition of terms
‘Falcon Windows’ will be referred to as ‘We’ or ‘Us’ within this information. Any users of the www.falconwindows.net website and any parties making enquiries by email, telephone or post are referred to as ‘You’ or ‘Your’.
Use of / access to our website is subject to acceptance of these Terms and Conditions. If you do not agree to these conditions, you should stop using the site at once.
Accuracy of information
Reasonable effort is made to ensure that information on our site will be accurate and up-to-date. This is done in good faith and we do not accept any liability for error or omission with regards to site content.
Our privacy statement only applies to our own websites.
Even where there is a hypertext link from this site, we do not accept responsibility for the content of any third party site. For third party websites, please refer to their own privacy statements.
We shall not be liable for any damages arising in contract, tort, or otherwise from the use of or inability to use this site, or any material contained in it, or from any action or decision taken as a result of using this site or any such material.
These Terms and Conditions are governed by English law.
Information we may collect
Like most other websites, we collect and use the data contained in server log files. The Falcon Windows website does not require membership at present. The information in the server log files include your IP (internet protocol) address, your ISP (internet service provider), the browser you used to visit our site (such as Internet Explorer or Chrome), the time you visited our site and which pages you visited throughout our site. This information is not linked to any information that is personally identifiable.
How information is used
We will analyse the information gathered to help us understand how well the website is performing.
The internet is an open public facility and no security measures are guaranteed. The Bateman’s Barn website uses reasonable security procedures to maintain the confidentiality of the information you provide.
Information collected via online / electronic enquiry
If you contact us with an enquiry electronically, we may collect and hold electronically contact information including name, telephone number and your email address.
We will use this information to:
- provide the requested service(s)
- monitor and improve the quality of our service
- profile and understand our customer base
We may need to pass some or all of the data collected to our UK-based service providers (eg banks, consultants or mailing houses) to enable us to provide the requested service. These third parties do not use your information other than as necessary to provide the requested service. We will also comply with requests for information from government agencies (UK or overseas) for law enforcement and compliance purposes. It may on occasion be appropriate to release this information to identify, contact or bring legal action against a person who may be causing injury or interference with another person’s rights or property.
Links to other websites
The Falcon Windows website may contain links to other websites of interest. Once you have used these links to leave our site, you should note that we do not have any control over that other website. Bateman’s Barn cannot be responsible for the protection and privacy of any information which you provide whilst visiting such sites and such sites are not governed by this privacy statement. Please exercise caution and look at the privacy statement applicable to the website in question.
Data Subject Access Request
You may ask us in writing for a copy of the information we hold about you (for which we may charge a fee) and to correct any inaccuracies in your information. We aim to respond to you within 31 days from the receipt of the request.
How to contact us
Unless otherwise stated, the copyright and any other rights in all material on this site are owned by Bateman’s Barn unless otherwise stated. You are only permitted to download and print extracts from this site under these conditions:
- No part of this site may be reproduced or stored in any other website without prior written consent of Falcon Windows.
- Use of documents and related images on this site is for information and/or personal, non-commercial use only.
- Copies of these pages saved on any storage medium may only be used for viewing purposes or to print extracts for personal, non-commercial use.
- The Falcon Windows copyright notice must appear in all copies.
- Documents or related images and materials on this site are not to be modified.
Cookies on this web site
Further information is provided below.
What are cookies ?
Taken from www.allaboutcookies.org
Also known as browser cookies or tracking cookies, cookies are small, often encrypted text files, located in browser directories. They are used by web developers to help users navigate their web sites efficiently and perform certain functions. Due to their core role of enhancing/enabling usability or site processes, disabling cookies may prevent users from using certain web sites.
Cookies are created when a user's browser loads a particular web site. The web site sends information to the browser which then creates a text file. Every time the user goes back to the same web site, the browser retrieves and sends this file to the web site's server. Computer Cookies are created not just by the web site the user is browsing but also by other web sites that run ads, widgets, or other elements on the page being loaded. These cookies regulate how the ads appear or how the widgets and other elements function on the page.
What cookies do we use ?
We use the following essential and performance based cookies on our web site:
These cookies may be created if you watch our web Presenters video or homepage video.
Google Analytics give us statistical information about visits to our web site. We use this information to make improvements to our web site by analysing this information. The cookies collect information in an anonymous form, including the number of visitors to the site, where visitors have come to the site from and the pages they visited.
Cookies can be enabled or disabled in your web browser. For further details please visit www.allaboutcookies.org or the help menu in your browser.
At Falcon Windows we endeavour to use as many images taken of our own installations as possible and thank our team for their diligence in collecting these records of our ongoing work. We would also like to thank its wide range of suppliers for their kind support through any photos, illustrations and marketing materials supplied either directly or through their online presence.
Product information on this website
At Falcon Windows we supply an ever-growing range of products and quality services. It is our aim to keep information included in this website as up to date as possible. We would however like to acknowledge that our innovative suppliers are always updating their products and specifications. Although these revisions come to our attention to share with our customers face to face, on occasion they may take a little longer to be included in our web presentations.
We thank our customers for their understanding on this matter.
Please give us a call if you have any queries, the Falcon Windows team are here to help with support, advice and the right price for any of our quality windows, doors or conservatories.